Pionite® Adhesives is a complete line of the best quality adhesives made with robust high solids formulas for dependable performance and value.
Pionite Adhesives are designed for countertops, store fixtures, architectural millwork, trade show exhibits, custom furniture, manufactured homes, recreational vehicles, marine boat building and use on construction job sites. Our line is designed to meet your needs with a wide range of sizes including aerosol canisters, aerosol cans and bulk pails and drums. Pionite Adhesives include SCAQMD & OTC Compliant, non-Chlorinated products with low VOC’s and fast tack.
Please call 866-735-9876 for more information.
PT2 is a high performance and versatile industrial strength contact adhesive. Water resistant and temperature resistant to over 200°F, PT2 is designed for bonding a wide range of substrates to include PIONITE decorative laminates and veneers, fiberglass, glass, upholstery, fabrics, foam, auto headliners, cork and particle board.
Pionite PT2 is designed to be applied to both surfaces about to be joined. Spray an even coat of adhesive with at least 80% to 100% coverage of each surface. Allow to dry 2-4 minutes until tacky. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease or oil. Ensure that the adhesives and substrates are at 60°F or higher. If surfaces are porous, a second coat is recommended after the first has dried and become tacky.
After use, do not close the valve. Leave the gun and hose connected to the canister. Recommended to store canister off the floor if temperatures below 60°F.
All available in Clear (C) or Red (R)
PT3 is a high performance and versatile industrial strength contact adhesive. Water resistant and temperature resistant to over 200°F, PT3 is designed for bonding a wide range of substrates to include PIONITE decorative laminates and veneers, fiberglass, glass, upholstery, fabrics, foam, auto headliners, cork and particle board.
Pionite PT3 is designed to be applied to both surfaces about to be joined. Spray an even coat of adhesive with at least 80% to 100% coverage of each surface. Allow to dry 3-5 minutes until tacky. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease, oil or other contaminants. Ensure that the adhesives and substrates are at 60°F or higher. If surfaces are porous, a second coat is recommended after the first has dried and become tacky.
After use, do not close the valve. Leave the gun and hose connected to the canister. Recommended to store canister off the floor if temperatures below 60°F.
All available in Clear (C) or Red (R)
PT25 is a high performance and versatile industrial strength contact adhesive. Water resistant and temperature resistant to over 200°F, PT25 is designed for bonding a wide range of substrates to include PIONITE decorative laminates and veneers, fiberglass, glass, upholstery, fabrics, foam, auto headliners, cork and particle board.
Pionite PT25 is designed to be applied to both surfaces about to be joined. Spray an even coat of adhesive with at least 80% to 100% coverage of each surface. Allow to dry 3-5 minutes until tacky. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease, oil or other contaminants. Ensure that the adhesives and substrates are at 60°F or higher. If surfaces are porous, a second coat is recommended after the first has dried and become tacky.
After use, do not close the valve. Leave the gun and hose connected to the canister. Recommended to store canister off the floor if temperatures below 60°F.
All available in Clear (C) or Red (R)
PT8 is a high strength contact adhesive with excellent performance characteristics. Applied on both surfaces to be adhered, PT8 is a high strength, high temperature contact adhesive providing strong permanent bonds for a wide variety of substrates to include PIONITE decorative laminates and veneers, fiberglass, glass, upholstery, fabrics, foam, auto headliners, cork and particle board. As a single surface application, its high tack and repositionability make PT8 an ideal adhesive for quick temporary bonding. Formulated with extremely low VOCs to comply with CA and OTC states regulations.
For strong permanent bonds, apply PT8 to both surfaces to be bonded. For repositionable temporary bonds, apply Pionite PT8 evenly to one side of the substrates to be bonded. Spray an even coat of adhesive with at least 80% to 100% coverage. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease or oil. Ensure that the adhesives and substrates are at 60°F or higher.
After use, do not close the valve. Leave the gun and hose connected to the canister. Recommended to store canister off the floor if temperatures below 60°F.
All available in Clear (C) or Red (R)
PT12 is a high performance and versatile industrial strength contact adhesive. Water resistant and temperature resistant to over 200°F, PT12 is designed for bonding a wide range of substrates to include PIONITE decorative laminates and veneers, fiberglass, glass, upholstery, fabrics, foam, auto headliners, cork and particle board.
Pionite PT12 is designed to be applied to both surfaces about to be joined. Spray an even coat of adhesive with at least 80% to 100% coverage on each surface. Allow to dry 2-4 minutes until tacky. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease or oil. Ensure that the adhesives and substrates are at 60°F or higher. If surfaces are porous, a second coat is recommended after the first has dried and become tacky.
After use, do not close the valve. Leave the gun and hose connected to the canister. Recommended to store canister off the floor if temperatures below 60°F.
All available in Clear (C) or Red (R)
PT13 is a high performance and versatile industrial strength contact adhesive. Water resistant and temperature resistant to over 200°F, PT13is designed for bonding a wide range of substrates to include PIONITE decorative laminates and veneers, fiberglass, glass, upholstery, fabrics, foam, auto headliners, cork and particle board.
Pionite PT13 is designed to be applied to both surfaces about to be joined. Spray an even coat of adhesive with at least 80% to 100% coverage on each surface. Allow to dry 3-5 minutes until tacky. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease, oil or other contaminants. Ensure that the adhesives and substrates are at 60°F or higher. If surfaces are porous, a second coat is recommended after the first has dried and become tacky.
After use, do not close the valve. Leave the gun and hose connected to the canister. Recommended to store canister off the floor if temperatures below 60°F.
All available in Clear (C) or Red (R)
PT18 is a multi-purpose industrial contact adhesive specifically designed for air assist spray application. Its excellent performance characteristics combined with its extended open time and CA compliance make it a truly superior adhesive. Applied on both surfaces to be adhered, PT18 is a high strength, high temperature contact adhesive providing strong permanent bonds for a wide variety of substrates to include PIONITE decorative laminates and veneers, fiberglass, glass, upholstery, fabrics, foam, auto headliners, cork and particle board. As a single surface application, its high tack and repositionability make PT18 an ideal adhesive for quick temporary bonding. Formulated with extremely low VOCs to comply with CA and OTC states regulations.
For strong permanent bonds, apply PT18 to both surfaces to be bonded. For repositionable temporary bonds, apply Pionite PT18 evenly to one side of the substrates to be bonded. Spray an even coat of adhesive with at least 80% to 100% coverage. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease or oil. Ensure that the adhesives and substrates are at 60°F or higher.
After use, do not close the valve. Leave the gun and hose connected to the canister. Recommended to store canister off the floor if temperatures below 60°F.
All available in Clear (C) or Red (R)
PT7 is a high solids spray grade contact adhesive designed for mass production. It is suitable for permanently bonding a wide range of materials. Water resistant and temperature resistant to over 200°F. Recommended for flat work applications.
Pionite PT7 is designed to be applied to both surfaces about to be joined. Spray an even coat of adhesive on both surfaces. Allow to tack. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease or oil. Ensure that the adhesives and substrates are at 60°F or higher. If assembly is delayed and the adhesive becomes too dry, apply a light coating again.
After use, do not close the valve. Leave the gun and hose connected to the canister. Recommended to store canister off the floor if temperatures below 60°F.
All available in Clear (C) or Red (R)
PT9 is a high solids spray grade neoprene based contact adhesive designed for postforming and production efficiency. It is suitable for permanently bonding a wide range of materials. Water resistant and temperature resistant to over 200°F. Suitable for most production postforming applications.
Pionite PT9 is designed to be applied to both surfaces about to be joined. Spray an even coat of adhesive on both surfaces. Allow to tack. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease or oil. Ensure that the adhesives and substrates are at60°F or higher. If assembly is delayed and the adhesive becomes too dry, apply a light coating again.
After use, do not close the valve. Leave the gun and hose connected to the canister. Recommended to store canister off the floor if temperatures below 60°F.
All available in Clear (C) or Red (R)
PT11 is a versatile, robust water based contact adhesive designed to provide
strong permanent bonds on a wide range of materials to include PIONITE decorative laminates and veneers, fiberglass, glass, cork, particle board and foam. It will not attack cells in expanded styrene and other foam materials. Water resistant and temperature resistant to over 200°F.
Pionite PT11 is designed to be applied to both surfaces about to be joined. Spray or roll an even coat of adhesive on both surfaces. Allow to tack. Place the surfaces together and apply pressure evenly across the full bonding surface. For best results: Make sure that the surfaces are dry and free from dirt, grease or oil. Ensure that the adhesives and substrates are at 60°F or higher.
Store in clean, dry area. Protect from freezing.
Appearance: Liquid, white or green
Base: Synthetic polymers
Solvent: Water based, no solvents
Solids %: 38 – 40%
Density: 9.2 lb/gal
Flash point: none
Shelf Life: 12 months (unopened)
Freezing: Protect from freezing.
All available in Clear (C) or Red (R)
PT1W is a superior wood glue for interior woodworking such as cabinetry and furniture. Designed to bond softwoods, hardwoods and composites, it is an excellent adhesive for assembly, doweling, edge or face gluing. Its strong initial tack and strong bond strength make it excellent for wood repairs.
Pionite PT1W is designed to be applied to one surface then assembled and clamped for at least 30 minutes. For best results: Make sure that the surfaces are dry and free from dirt, grease or oil. Ensure that the adhesives and substrates are at 50°F or higher. Wipe all excess glue with clean moist cloth. Not recommended for Exterior use or wet, high moisture conditions.
After use, close container tightly. Store in cool dry location at 50-80°F. Protect from freezing.
Appearance: White Liquid
Specific Gravity: 1.07 to 1.11 gm/PTCC
Solvent: Water based, no solvents
Flashpoint: > 200°F
Flammability: Non-Flammable per ASTM 681-04
Shelf Life: 12 months
Freezing: Protect from freezing.
All available in Clear (C) or Red (R)
PT1Y is a superior wood glue for interior woodworking such as cabinetry and furniture. Designed to bond softwoods, hardwoods and composites, it is an excellent adhesive for assembly, doweling, edge or face gluing. Its strong initial tack and strong bond strength make it excellent for wood repairs.
Pionite PT1Y is designed to be applied to one surface then assembled and clamped for at least 30 minutes. For best results: Make sure that the surfaces are dry and free from dirt, grease or oil. Ensure that the adhesives and substrates are at 50°F or higher. Wipe all excess glue with clean moist cloth. Not recommended for Exterior use or wet, high moisture conditions.
After use, close container tightly. Store in cool dry location at 50-80°F. Protect from freezing.
All available in Clear (C) or Red (R)
PTCC is a citrus-based adhesive cleaner designed to remove most adhesives from unwanted surfaces. Removes adhesives, oil, ink, decals, tar and similar residues.
Pionite PTCC is designed to remove unwanted adhesive. Spray a heavy coat over the area to be cleaned. For best results, wait 3 to 5 minutes before wiping clear. For unusually difficult jobs, apply second coat of PTCC to area after first wiping off first application coat. Do not apply new coat of adhesive until the surface is completely clean of PTCC residue.
Do not store in direct sunlight or in areas with temperatures of 120°F or greater.
All available in Clear (C) or Red (R)